Refit: To-Do list

Research

 safe mast climbing solo

Caribbean cooking 

Princess auto

• 18mm hex by  3/4" socket  18mm allen key?

Home depot  

• anodes 4 pcs

• 
  

Plastic world

•  1/8 or 3/16" frosted black acrylic, 12X.5.75, 
• cover for rhs of drop down is 12" X 5.75"  revise switching
• 14X5
• 5X7
• , 

Home 

• Staysail sheets
• vang for outboard lift

Chandler now

• 6mm tack shackle, 30mm gap, 55mm depth  
• staysail winch screws.  M8X 40mm flat head allen
• spare head shackle  30mm wide D shackle
• Facnor  F10 (6) and F20 (7)  pins.  need 2 and 6 respectively, 2 spares.      (repl with m6X70mm if necessary                              
• Diesel breather hoses 22mm id, est 150” length
• identify L&S cylinder  
• measure drag link 
• measure anchor chain. 10mm g40
• identify batten pockets  (need sail)
• Seajet 038 navy blue 
• cutlass bearings
• shaft seals
• tool for facnor cars

Grenada work

Hull on the hard

• Install new windows 
• paint welds/hand holds
• replace fuel tank vent hoses 22mm ID X 150in
• new screws for staysail winches
• new gasket for stbd fuel tank lid
• confirm RH prop rotation Confirm pitch is 21deg.
• bottom paint and zincs
• clean water tanks, install additional anodes
• complete watermaker install
• Secure windlass remote receiver.
• could the second one be connected?
• add valve to fridge drain (3/4" barb)

• cut open fridge access, install panel
• determine source of fridge leak.  not liner  condensation on coolant line?  Insulate?
• engine oil and filters
• disassemble and clean windpilot clutch
• repair or replace volvo engine control plate
• lube engine cables
• replace stbd solar cables - 4m ea
• replace cutlass bearing and order spare
• pull ethernet cables and install switch
• rewire drop-front panel and other switching.
• relocate USB charger in fwd cab to upper shelf

mast

• Buy New antenna, cables   RG8X   80’/run
• https://www.practical-sailor.com/marine-electronics/3db-vhf-antenna-test  
• Digital 222 3db antenna recommended
• Windex 15 purchased in Martinique -  install
• Tricolour light (install) 
• Foredeck light (install)
• replace wind sensor with wired
• Service sheaves
• Tighten furler sections
• relieve radar cable
• washers for gooseneck shim
• end for end jib and staysail halyards.
• messenger for unused halyard
• replace dyneema check stays
• replace flag halyards  (small block?) 
• 
  

Canvas 

• dinghy chaps  michael 4735346866 whatsapp
• Bags/bucket for rope anchor rodes?
• NV canvas order

metal work

•     liferaft cradle
•     dorade vents
•     anchor chute

• 
  

B&G and victron Tech 

• WS320  - this is not a robust or reliable system. Replace with ws310 or high end uk version end u
• 
  
  
• 
  

AR 007372 1000w Windlass  (Caraibe Marine, Martinique)

• Free seizedWindlass clutch.   This willl require a tool, star or 18mm X15mm min square drive operable by a breaker bar or impact driver.
• Install emergency windlass switch.
• If non repairable replacement is the X2 model
• 
  
• 
  
  

Autopilot/Steering  (Martinique)

• LeComble and schmidt spares
• 
  
  
• Whitlock rose joints
• change fluid in L&S
• Spares for l&s
• 1.5" blocks for windpilot double swivel, two singles
• dymeema core line for steering?

• Facnor  F10 (6) and F20 (7)  pins.  need 2 and 6 respectively, 2 spares.      (repl with m6X70mm if necessary                              
• Batten pockets identify
• tack shackle 3/4" deeper

• 2c cable for watermaker lift pump 7m
• lifting harness for dinghy motor
• modify lifting tackle with cleat at running end
• 3 pin Connector for windlass remote (to make emergency spare or plug in )
• Louvered  engine ducts (le ship)
• Dinghy running light
• Soft shackles for runners
• 16mm hose barb fittings for fridge pump,  shurflo 4128-110-E04  
• silva 70 bracket (home)
• 
• 
  
• Relay AD L43150. (Std 4-terminal relay)
• Larger relay for autopilot spare  - 4 terminal but bigger tabs
• spare latch hooks Whitewater marine 2600SS.
• 
  
• 
  
  
• new water tank lids. ?
• Tackle boxes approx 11X7.5

From ALUBAT France (Ship to Grenada)

• plugs for rudder bolts
• Screws for plexi
• plastic for CB glides
• seals forr hydroem pump
• Loop

 Canvas Work

• New Dodger
• Dinghy Chaps
• Bag for spare anchor rode
• sun shade forr bimini ext.

Metal Fab

• make anchor chute
• Alu liferaft cradle 
• Dorade boxes

Projects at home

• dimensions for pot lid fingers'.  Lip is 1 7/8”
• cover for rhs of drop down is 12" X 5.75"  revise switching
• 14X5
• 5X7
• breaker bar 18mmsq X 15+mm deep
• Shelf for fridge 
• binocs holder
• Flashlight holder 
• Opinel holder
• Horn holder 
• Thermos holder for between towel racks 
• Spice rack for jars  1.875X4.25
• Basket for fruit and bread
• Maple cutting board to fill weird hole behind range 
• Frame for top of drawers (for hardware boxes). 24.5x18.5x2.5
• Parts to make fastener box at foot of owners berth 
• make dropboard holders
• glasses and flashlights binocs, hb compass holder
• Canvas bags for spares
• PT holder w sharpening steel. 
• make cover for halyard winch motor 
• Inside 10X14”, 
• 2.5” high to clear motor 
• Curve is minimal.  Oddly
• make new cockpit cushions   59x20.25
• Make More G10
• anodes for water tanks
• Bag for stern anchor rode need volume 18x10x10 rope only
• Holder for bolt cutters
• Coffee grinder and moka pot holder 
• Salt and pepper holder 
• Simrad Ethernet cables and field attachable jacks 
• Ethernet switch
• Low friction blocks for windpilot 
• New treads for companionway
• shelf supports for galley shelf - 28" X2
• fish club
• 3 more hubs for water tanks

Projects on Boat

• replace steering fittings
• improve anchor locker divider and isolation
• Heat shrink boot port side 
• Spray dodger again.
• test hydrogen
• install starboard side fuel tank gasket
• replace fuel breather hoses.
• Refin companionway area and new treads. 
• How to store pot lids?  Plastic fingers!
• Install watermaker
• remove and reinstall hyd pump.  Check leak. 
• reinstall traveller screws
• small fuse block for ent. Stereo, vhf on same cut 
• Hook for anchor locker lid 
• Cleat for anchor safety line 
• fix dodger snap
• Lift latch for fwd floor
• repair dodger straps
• mount HH VHF charging cradles, hang commanmic 
• Update navionics 
• Rack for screwdrivers/oft-used tools.  
• revise and relabel panel, label autopilot power
• Revise switches in drop down  (new panel)
• glue trim at nav cabinet door and cabin sole near galley
• Fix outboard
• Install stbd  Fuel tank gaskets 
• Replace garden hoses on fuel tank vents 
• hang cleats for dock lines
• BBQ mount?  Fcking thing….
• STAPLE OVERHEAD
  Mount first aid kit by galley
• relocate liferaft cradle to cabin top
• mount ipad etc for backup behind nav station
• Check screws and pads on hinges -fwd ps anchor locker, lowest helm seat plate, upper 3 on SS hatch lid 
• improve winch button mounting
• Drill finger hole in large panel and fit small panel properly in stbd aft cabin
  Cut access hatch for breakers in p/s aft cabin
• repair ps aft cabin plywood
  Make fastener storage box fwd of drawer
• safety wire dst 810 when replaced.  Locate blocking plug 
• inventory above water skin fittings.
• Relocate cabin heater.
• Install Propane solenoid 
• longer screws/nuts for staysail winches  M8X40
• Finish 220v wiring (box for splices  in owners cabin)
• Install new gas detector/heat sensor
• install reading/dome lights
• install one more anode in stbd water tank, 3 more in port.  (I have two hubs aboard). 
• Water filter at galley tap.  
• relocate extra chain to chain locker 
• program multi plus 

Rope work

• Make mooring bridle lines
• Make second anchor bridle
• make dinghy hanger bridle with shackles
• lanyards for pelican hooks and shackles
• Make lead line for when dst fails again 
• means of latching dinghy to boat?
• flag halyards
• Short length of nylon rode for tandem anchoring
• 
  

Engine spares

• Better and spare alternator 
• starter  have one
• order spare volvo penta shaft seal  828422
• cutlass bearings
• Spare Lift pump  got
• replacement engine panel

Rig Parts

• 25mm velcro for furler pre-feeders  DONE
• new staysail sheets  12mm dia X 16m ea  may hae in loft
• 1.5" low friction blocks for windpilot  Have one shaefer double.   
• 
  

items to purchase for Oct 2026

• Egg containers DONE
• Windlass oil seal 35-45-7  DONE
• #4 mokka pot gaskets   DONE
• Egg containers 2X6 DONE
• Watermaker hose.  1/2” of needs maybe 4m if possible to splice.  , same.   Otherwise - 9m?  DONE
• T27 torx bit  DONE
• 5266ca for 125vac inverter  DONE
• faston terminals - selection DONE
• cable ties - orange and yellow DONE
• green electrical tape. DONE
• jumpers/alligator clips DONE
• Repair lofrans remote DONE
• needle-nosed pliers DONE
• 
  
• Field attachable mm and ff nmea
• Switch and Ethernet cables for b&g
• RJ45 crimper
• one navico ethernet cable
• Connector/jb box/system for mast 
• make Sail ties

• toilet paper holders
• max 15"wide monitor, ideally 12v
• larger bowls to match existing?
• myers hub for water tank
• Brady labels
• more water tank anodes
• 6 usb chargers (2 ordered)
• Small printer for customs docs
• 
  
• Bring more star and puckboard
• suzuki flush fitting suzuki 55181-95200
• suzuki carb rebuild kit
• 12v 23A type batteries for windlass remotes
• known good apple cables
• 8" zipper for backpack

• diesel resistant Gasket material 
• Bag for reels
• Freezer packs for fridge/cooler.
• Larger cooler bag for defrosting 
• 2 ea quality 40a breakers (hydro gen, max 350w, 220 typ?)
• Npt to push on fittings
• 
  
• cockpit light?
• 
  
• Better selection of woodworking files
• Small file handle 
• Small hole saw mandrel. 
• Bigger bowls to match existing?
• Cylindrical knobs for panel - 12x22mm
• Masher 
• Diff coloured tool bags/luggage tags 
• Material for companionway steps?
• case/RAM for iPad A16

Future work

• Reconfigure 220v switching
• Reconfigure DC switching and access 
• relocate engine panel
• Ventilation - dorades fwd of main cabin hatch and dome on foredeck?
• Replace pod with scanstrut SPH-31-w or lewmar extra wide

Anchor handling 

• Add chain ramp
• Move additional chain to anchor locker
• Plastic for floor 
• Hangers for mooring/bridle lines 
• Second bower anchor

Instrument strategy

• Master/slave both mfds using commercial Ethernet swith
• Update software
• Wired wind inst
• Redundant iPad and gps
• Test Redundant gps for computer/opencpn
• Ram mount for iPad A16
• Din rail mount Ethernet switch 
• Rj45 crimper and connectors 
• Long simrad Ethernet cable 

• anodes 110 (4.5")  
• anodes 140mm  4.5 and 5.5" 
• TACTIX 320078 parts bin  14in
• M10, m8, m6 taps
• solder sucker
• curtain fabric Fabricland (blue) 21840 21.99<20% pitch black 7635AD $19<50%
• More Mika sanding screen things 
• Cable gland Panzer gauge 13.5
• 
  

brush for vaccuum

document/inventory

• Document and indicate through hulls
• anodes
• Document and assess critical hoses 
• Document compass and pedestal cover design
• Document engine belts 
• template fitted Tool roll for wrenches
• measure large hatches for bug screens
• determine tool storage strategy
• Water tank lids, make, model, size.
• Engine mounts, including durometer stamp
• Stanchion  sleeves in base
• Shelf in fridge   
• teak, oak
• material for delrin slides
• measure for jacklines and check
• shorepower adaptors
• 30a 125VAC NEMA M>IEC blue female  (to adapt shore power)
• 15A 125VAC NEMA M > IEC blue female (to adapt shore power)
• IEC standard plug to NEMA Female - mark 125VAC only